Wednesday, July 27, 2011

Heckler & Koch G41

Heckler & Koch G41
The Heckler & Koch G41 is a German 5.56mm assault rifle introduced in 1981 and produced in limited quantities by Heckler & Koch. It was designed to replace the 5.56mm HK33 in service providing a more modern weapon platform compatible with contemporary NATO standards. It is chambered for the 5.56x45mm NATO cartridge and can use both SS109 and M193 ammunition. Assembly of the G41 has been discontinued by Heckler & Koch, however, production rights to the rifle were acquired by the Italian arms manufacturer Luigi Franchi.




G41
Type Assault rifle
Place of origin West Germany
Service history
Used by Italy, Spain, Turkey, United States, Germany
Wars 2007 Lebanon conflict
Production history
Designer Heckler & Koch
Manufacturer Heckler & Koch
Produced 1987 - 1996
Specifications
Weight G41/A1: 4.1 kg (9.04 lb)
G41A2/A3: 4.4 kg (9.7 lb)
G41K: 4.3 kg (9.5 lb)
Length G41/A1: 997 mm (39.3 in)
G41A2/A3: 985 mm (38.8 in) stock extended / 800 mm (31.5 in) stock folded
G41K: 930 mm (36.6 in) stock extended / 740 mm (29.1 in) stock retracted
Barrel length G41: 450 mm (17.7 in)
G41K: 380 mm (15.0 in)
Width 72 mm (2.8 in)
Height 214 mm (8.4 in)

Cartridge 5.56x45mm NATO
Action Roller delayed blowback
Rate of fire 850 rounds/min
Muzzle velocity G41 using SS109: 920 m/s (3,018 ft/s)
G41K using SS109: 880 m/s (2,887.1 ft/s)
G41 using M193: 950 m/s (3,116.8 ft/s)
G41K using M193: 910 m/s (2,985.6 ft/s)
Effective range 100—400 m sight adjustments
Feed system Various STANAG magazines
Sights Rotary rear diopter drum, hooded front post

Operating mechanism

The G41's engineering origins lay in the 7.62mm G3 battle rifle. It is a selective fire automatic weapon that employs a roller-delayed blowback system of operation. The two-piece bolt mechanism consists of a bolt head that contains two cylindrical rollers and a wedge-shaped locking piece, attached to a heavy bolt carrier. When fired, the build-up of gas pressure generated by the ignited powder charge exerts rearward pressure on the bolt, which is then transferred onto the rollers. The rollers are cammed inward against appropriately shaped walls in the barrel extension, displacing the locking piece. The geometry of the camming ramps on the wedge-like locking piece ensure a rearward velocity that is greater than that of the bolt. This ensures that the bullet has left the barrel, allowing bore pressures to drop to a safe level before the rollers are fully retracted, clearing the barrel extension notches and releasing the bolt, which is then engaged by the bolt carrier and withdraws together with the entire moving assembly.

Features

The spent cartridge casing extractor is installed inside the bolt head, while the tilting lever ejector is contained in the trigger housing. The rifle is hammer-fired and has a trigger group with a fire control selector that enables semi-automatic, burst and continuous fire. The fire selector's positions are marked with bullet pictograms and it also serves as a manual safety against unintentional discharge. The selector is ambidextrous and its lever is mirrored on both sides of the trigger housing. In the "safe" position, the trigger and sear are disabled.

The firearm uses Nato-standard aluminium box magazines (from the M16 rifle) with a capacity of 30 rounds. The magazine release is located on the left side of the rifle, above the magazine well.

The weapon incorporates a manual forward assist that can be used to positively close the bolt, similar to the one used on the American M16A1 rifle, and a side-folding heavy-gauge wire carrying handle which resembles that of the FN FAL. It also has a "hold-open" bolt catch which holds the bolt open after the last round in the magazine has been fired (the bolt release button is just above the magazine release) and has a spring-loaded dust cover that seals the ejection port from debris.

Barrel

The cold hammer-forged barrel has a hexagonal polygonal bore. It comes rifled for either the NATO-standard, Belgian SS109 62 grain bullet with a twist of 178 mm (1:7 in) or in a 305 mm (1:12 in) twist for use with American ammunition with the M193 55 grain projectile. The bore chamber is fluted to assist in the extraction of spent cartridges. The barrel is equipped with a flash suppressor that is also designed to launch rifle grenades.

Sights

The G41 has mechanically adjustable iron sights with a rear rotating diopter drum and hooded front post. The rear sight drum has three apertures of different diameter calibrated for firing at distances of 200, 300 and 400 m and a triangular notch setting preset for firing at 100 m. The receiver housing has recesses in the top cover that permit the use of H&K's proprietary clamp mounts and adapters for NATO-standard optics (such as the Hensoldt 4x24 telescopic sight).

Accessories

Many accessories are based on NATO standard or previously issued items.Link

The rifle can be fitted with a barrel-mounted bipod based on the one issued with the M16A1's cleaning kit. It also uses the bayonet from the G3. It also can mount the FERO Z24-G 4x24 optical sight on a NATO-standard Picatinny Rail on the receiver.

The G41 can also mount a detachable 40 mm HK79 grenade launcher that replaces the synthetic forearm. The weapon in this configuration is known as the G41TGS, or "Tactical Group Support".

Heckler & Koch G41 Variants

  • G41: This is the standard model with a fixed stock and 178 mm (1:7 in) rifling.
  • G41A1: This model has a fixed stock and 305 mm (1:12 in) rifling.
  • G41A2: This model has a telescoping shoulder stock and 178 mm (1:7 in) rifling.
  • G41A3: This model features a telescopic stock and a 305 mm (1:12 in) rifling pitch.
  • G41K: This is a carbine (K—Karabiner) variant of the G41A2 with a shortened 380 mm (15.0 in) barrel (reduced in length to the base of the foresight), 178 mm (1:7 in) rifling twist rate and a telescopic stock. The G41K is too short to accept the HK79 or fire rifle grenades.
  • G41TGS: The "Tactical Group Support" model adds a HK79 grenade launcher.
  • LF G41: Luigi Franchi made a sample run of the G41, G41A2 and G41K in 1988 for possible production under license; these were later modified for trials by the Italian Army. It differed from the Heckler & Koch model in that it had a polygonal 4-groove barrel with a chromed bore. When the G41 was rejected by the German Bundeswehr in 1989, it was dropped from consideration and the improved Beretta AR 70/90 was chosen instead in 1990. The LF G41 however entered use with the Italian commando frogmen (COMSUBIN).

No comments:

Post a Comment

Related Posts Plugin for WordPress, Blogger...